pdf download link

Material for Value-Tec fine, industrial and fibre grip tweezers

Introduction
The material used for manufacturing the Value-Tec fine, industrial and fibre grip tweezers is a selected grade of non-magnetic AISI 202 stainless steel.

It is used for the following Value-Tec tweezers:
#50-014010 through #50-014220 Value-Tec  fine tweezers
#50-014X20 through #50-014X70 Value-Tec reversed fine tweezers
#50-014310 through #50-014386 Value-Tec industrial strong tweezers
#50-014462 through #50-014482 Value-Tec fiber grip tweezers

General remarks:

  • AISI 202 is an austenitic stainless steel (DIN 1.4373, X12CrMnNNi 18-9-5) and is a cost effective replacement for 304, 302 and 310 stainless steel with a lower Ni content
  • Contains 17 – 19 wt% Chromium and contains significant amounts of Manganese and Nickel as additional alloy component. N is added to increase strength.
  • Normally non-magnetic, but becomes magnetic when cold worked
  • Can be hardened by heat treatment and precipitation hardening
  • Can be work hardened, annealing is recommended for stress relieving
  • Moderate corrosion resistance to most solvents, salts and moderate acids
  • Generally used where both strength and corrosion resistance are required
  • Typical applications include tweezers, tools, cooking equipment, hose clamps and architectural products

General composition of AISI 202

Element

Wt. %

C

≤0.15

Cr

17.0 – 19.0

Ni

4.0 – 6.0

Mn

7.5 – 10.0

Si

≤1.0

N

≤0.25

P

≤0.06

S

≤0.03

Fe

Balance

Properties of AISI 304<

Mechanical Properties

State

Annealed

Density

7.8 g/cm3

Hardness Rockwell B

90

Hardness Rockwell C

27

Tensile strength, ultimate

515 MPa

Tensile strength, yield

275 MPa

Elongation until break

40%

Modulus of Elasticity

207 GPa

Poisson's ratio

0.29

Thermal Properties

Coefficient of thermal linear expansion

17.3 x 10-6 /°C   (20-100°C)

Coefficient of linear thermal expansion

17.8 x 10-6/°C    (20-300°C)

Specific heat capacity

0.50 J/(g.K)

Thermal conductivity

16.3W/(m.K)

Continuous use (service) temperature

500°C

Maximum service temperature (short)

870°C

Electrical Properties

Resistivity

0.69 x 10-4 Ohm.cm



TSB 50-014010 Material for Value-Tec fine, industrial and fibre grip tweezers Revision 1



SEM Supplies

TEM Supplies

Calibration

Sample Preparation

AFM / SPM

  Product Menu with Images
  SEM Sample Stubs
  Carbon Tabs
  Sample Stub Adapters
  SEM Stage Adapters
  SEM Sample Holders
  SEM Preparation Stands
  Filaments / Cathodes
  Silicon Finder Grid
  Gatan 3View Pins
  FEI Volumescope Pins
  SEM Stub Storage Boxes
  Phenom Supplies
  JEOL NeoScope Supplies
  Hitachi TM Series Supplies
  Field & Lab Sampler Kits
  FlowView liquid sample Kit

Instruments

  Acoustic Enclosures
  Cressington SEM coaters
  TEM Sample Prep
  Diaphragm Pump
  Rotary vacuum Pump
  Precision diamond saw  
  TEM Grids
  TEM Support Films
  Silicon Nitride Films
  K-Kit Wet Cell Holder
  Graphene Films
  TEM Grid Boxes
  Cryo Grid Boxes
  TEM Sample Staining
  3mm Embedding Tubes
  Filaments/Cathodes
  Eyelash Manipulators

Cryo Supplies

  Cryo Grid Boxes
  Other Cryo Supplies

FIB Supplies

  FIB Lift-out Grids
  FIB Low Profile Stubs
  FIB Grid Holders
  FIB Pre-tilt Holders
  FIB Pre-tilt stubs
  FIB Grid Boxes
  SEM / FIB Magn. Calib.
  SEM Res. Test Spec.
  EDS / WDS Calibration
  TEM Calibration
  AFM / SPM Calibration
  LM Magn. Calibration

Vacuum Supplies

  Vacuum Gauges
  KF/NW Vacuum Parts
  KF/NW Vacuum Hoses
  ISO Vacuum flange parts
  Vacuum Oil and Grease
  Vacuum Sealant
  Diaphragm Pump
  Rotary vacuum Pump
  Vacuum Sample Storage
  Vacuum Pick-Up Pens

Sample Coating Supplies

  Sputter Targets
  Carbon Rods & Fibers
  Quartz QCM Crystals
  SEM Sample Coating Fluid

Evaporation Supplies

  Thermal Evaporation Sources
  Evaporation Materials
  Supports & Substrates
  SEM Preparation Stands
  Tweezers
  Probes & Picks
  Applicators & Swabs
  Plastic Transfer Pipettes
  Cutting Tools / Scissors
  Conductive Paint/Cement
  Conductive Tapes & Tabs
  Non-Conductive Adhesives
  Sample Storage
  Hand Tools
  Sorting Wire Mesh
  Preparation Surfaces
  Cleaning / Gloves
  Conductive Metal Powders
  Metallographic Sample Prep
  AFM/SPM Discs
  AFM/SPM Disc Pick-up Tool
  AFM/SPM Holders
  AFM/SPM Disc Storage
  Cantilever Tweezers
  AFM/SPM Discs Tweezers
  Nano-Tec Mica Discs
  HOPG Substrates

Light Microscopy

  Correlative Cover Slips
  Glass Microscope Slides
  Glass Cover Slips
  Quartz Microscope Slides
  Quartz Cover Slips
  Black Metal Slides
  Slide Storage Boxes
  LM Calibration
  Plastic Transfer Pipettes
  Optical Lens Tissue
  Glass Petri Dishes
  Digital Microscope
  PTFE Beakers