pdf download link

Material for EM-Tec SEM stub gripper tweezers

Order EM-Tec SEM stub gripper tweezers

The material used for manufacturing the EM-Tec SEM stub gripper tweezers is a selected grade of non-magnetic AISI 304.

It is used for the following products:
#50-050012 EM-Tec 127G.AM SEM stub gripper tweezers for Ø12.7mm (1/2”) grooved pin stubs
#50-050019 EM-Tec 190G.AM SEM stub gripper tweezers for Ø19.0mm (1”) grooved pin stubs
#50-050025 EM-Tec 254G.AM SEM stub gripper tweezers for Ø25.5mm (3/4”) grooved pin stubs
#50-050032 EM-Tec 318G.AM SEM stub gripper tweezers for Ø32.0mm (1-1/4”) grooved pin stubs
#50-050013 EM-Tec 12.AM scissor type SEM stub gripper tweezers for Ø12.7mm (1/2”) grooved pin stubs
#50-050026 EM-Tec 25.AM SEM scissor type stub gripper tweezers for Ø25.5mm (3/4”) grooved pin stubs
#50-050110 EM-Tec 95.AM SEM stub gripper tweezers for Ø9.5mm JEOL cylinder stubs
#50-050112 EM-Tec 122.AM SEM stub gripper tweezers for Ø12.2mm JEOL cylinder stubs
#50-050150 EM-Tec 150.AM SEM stub gripper tweezers for Ø15.0mm Hitachi and ISI cylinder stubs
#50-050250 EM-Tec 250.AM SEM stub gripper tweezers for Ø25.0mm JEOL and Hitachi cylinder stubs
#50-050320 EM-Tec 320.AM SEM stub gripper tweezers for Ø32.0mm JEOL and Hitachi cylinder stubs


General remarks:

  • AISI 304 is an austenitic stainless steel (DIN 1.4301, X5CrNi 18-10) and is the most common type of stainless steel
  • Contains 18 – 20 wt% Chromium and contains significant amounts of Nickel as additional alloy component
  • Normally non-magnetic, but becomes slightly magnetic when cold worked
  • Can not be hardened by heat treatment
  • Can be work hardened, annealing is recommended for stress relieving
  • Good corrosion resistance to most solvents, salts and moderate acids
  • Generally used where corrosion resistance is a requirement
  • Typical applications include tweezers for microscopy, electronic industry, fine mechanics and laboratory


General composition of AISI 304

Element Wt. %

C

≤0.08

Cr

18.0 – 20.0

Ni

8.0 – 10.5

Mn

≤2.0

Si

≤1.0

P

≤0.045

S

≤0.03

Fe

Balance


Properties of AISI 304

Mechanical Properties

State

Annealed

Density

8.0 g/cm3

Hardness Brinell

123

Hardness Rockwell B

70

Hardness Vickers

129

Tensile strength, ultimate

505 MPa

Tensile strength, yield

215 MPa

Yield stress, o.2%

≤200 Mpa

Elongation until break

70%

Modulus of Elasticity

195 GPa

Poisson's ratio

0.29

Thermal Properties

Coefficient of thermal linear expansion

17.3 x 10-6 /°C   (20-100°C)

Coefficient of linear thermal expansion

17.8 x 10-6/°C    (20-300°C)

Specific heat capacity

0.50 J/(g.K)

Thermal conductivity

16.2W/(m.K)

Continuous use (service) temperature

325°C

Maximum service temperature (short)

870°C

Electrical Properties

Resistivity

0.72 x 10-4 Ohm.cm



TSB 50-001010 Material for EM-Tec SEM stub gripper tweezers Revision 1




SEM Supplies

TEM Supplies

Calibration

Sample Preparation

AFM / SPM

  Product Menu with Images
  SEM Sample Stubs
  Carbon Tabs
  Sample Stub Adapters
  SEM Stage Adapters
  SEM Sample Holders
  SEM Preparation Stands
  Filaments / Cathodes
  Silicon Finder Grid
  Gatan 3View Pins
  FEI Volumescope Pins
  SEM Stub Storage Boxes
  Phenom Supplies
  JEOL NeoScope Supplies
  Hitachi TM Series Supplies
  Field & Lab Sampler Kits
  FlowView liquid sample Kit

Instruments

  Acoustic Enclosures
  Cressington SEM coaters
  TEM Sample Prep
  Diaphragm Pump
  Rotary vacuum Pump
  Precision diamond saw  
  TEM Grids
  TEM Support Films
  Silicon Nitride Films
  K-Kit Wet Cell Holder
  Graphene Films
  TEM Grid Boxes
  Cryo Grid Boxes
  TEM Sample Staining
  3mm Embedding Tubes
  Filaments/Cathodes
  Eyelash Manipulators

Cryo Supplies

  Cryo Grid Boxes
  Other Cryo Supplies

FIB Supplies

  FIB Lift-out Grids
  FIB Low Profile Stubs
  FIB Grid Holders
  FIB Pre-tilt Holders
  FIB Pre-tilt stubs
  FIB Grid Boxes
  SEM / FIB Magn. Calib.
  SEM Res. Test Spec.
  EDS / WDS Calibration
  TEM Calibration
  AFM / SPM Calibration
  LM Magn. Calibration

Vacuum Supplies

  Vacuum Gauges
  KF/NW Vacuum Parts
  KF/NW Vacuum Hoses
  ISO Vacuum flange parts
  Vacuum Oil and Grease
  Vacuum Sealant
  Diaphragm Pump
  Rotary vacuum Pump
  Vacuum Sample Storage
  Vacuum Pick-Up Pens

Sample Coating Supplies

  Sputter Targets
  Carbon Rods & Fibers
  Quartz QCM Crystals
  SEM Sample Coating Fluid

Evaporation Supplies

  Thermal Evaporation Sources
  Evaporation Materials
  Supports & Substrates
  SEM Preparation Stands
  Tweezers
  Probes & Picks
  Applicators & Swabs
  Plastic Transfer Pipettes
  Cutting Tools / Scissors
  Conductive Paint/Cement
  Conductive Tapes & Tabs
  Non-Conductive Adhesives
  Sample Storage
  Hand Tools
  Sorting Wire Mesh
  Preparation Surfaces
  Cleaning / Gloves
  Conductive Metal Powders
  Metallographic Sample Prep
  AFM/SPM Discs
  AFM/SPM Disc Pick-up Tool
  AFM/SPM Holders
  AFM/SPM Disc Storage
  Cantilever Tweezers
  AFM/SPM Discs Tweezers
  Nano-Tec Mica Discs
  HOPG Substrates

Light Microscopy

  Correlative Cover Slips
  Glass Microscope Slides
  Glass Cover Slips
  Quartz Microscope Slides
  Quartz Cover Slips
  Black Metal Slides
  Slide Storage Boxes
  LM Calibration
  Plastic Transfer Pipettes
  Optical Lens Tissue
  Glass Petri Dishes
  Digital Microscope
  PTFE Beakers